Adhesive and insulating

-50%New product
2710708 Pattex Rapid Adhesive 200 + 50ml (Mdf Kit Transparent 6 pcs/ctn) German technology Made in Turkey
in-stock
Pattex Rapid Adhesive 200 + 50ml (Mdf Kit Transparent 6 pcs/ctn) German technology Made in Turkey
Pattex MDF Kit is an adhesive set which consists of high viscosity cyanoacrylate adhesive and activator. Activator increases bonding strength by preventing the adhesive to be absorbed by the surface. With a high bonding strength, it is suitable for use on vertical surfaces as it will not drip or slump. It is particularly suited to bonding difficult substrates which have a porous or uneven nature since it increases bonding strength by preventing the adhesive to be absorbed by the surface. It is particularly used for fixing and repairing wooden parts. Suitable for MDF, wood, chip wood, rubber, most plastics, leather etc. Especially suitable for the applications where cure speed needs to be accelerated.
Pattex Adhesive Fast 2K 200Ml+50Ml 2710708
Pattex 2710708 2K Activator Instant Adhesive 200 Ml Aerosol+50 Ml Bottle
Two Component Instant Adhesive. Activator Increases Adhesion Strength by Preventing Adhesive from Being Absorbed by the Surface. Accelerates Adhesion.
Scope of application:
Bonding of Wooden Profiles.
Bonding of Mdf, Rubber, Chipboard, Plastic and Tire.
Repair And Fixing Of Wooden Parts.
Technicial Specifications
Color : Transparent
Hardening Time: 5 ~ 10 Sec
Chemical Structure : Adhesive : Cyanoacrylate.
Activator : Heptane
Viscosity : 1200-1700 Cps
Heat Resistance: -50°C to 80°C
Tensile Strength: 20 N/Mm2
Flash Point : >85°C
Shelf Life : 12 Months
Application
The surfaces to be bonded must be dry, clean, free from dust and oil. Squeeze the Activator Vertically 20 cm from the Surface. Wait 3 sec. Apply Pattex Instant Adhesive to the Same Surface. Bring Surfaces Together. Sticking Happens Instantly.
Attention! Activator is Flammable. Do not throw into fire. Do not breathe. Activator Box is Pressurized. Do not crush, do not puncture, protect from direct sunlight. Activator and Fast Adhesive Should Not Contact Skin And Eyes. In case of contact, wash with plenty of water and consult a doctor. Keep Out of the Reach of Children.
200 Ml Aerosol+50 Ml Bottle
-50%
Pattex SL212 Acetic silicone Transparent 280ml Code 2637449 German technology Made in Belgium
in-stock
Pattex SL212 Acetic silicone Transparent 280ml Code 2637449 German technology Made in Belgium
Pattex SL212 is ready-to-use silicone sealant for general purpose sealing and glazing applications (indoor and outdoor). Good adhesion to a variety of non-porous substrates, resistant ultra-violet radiation, waterproof, good chemical resistance, excellent elasticity.
-50%New product
Pattex 2370711 Super Glue liquid 3g Made in Ireland
in-stock
Pattex 2370711 Super Glue liquid 3g Made in Ireland
Pattex Super Glue – Liquid Super Glue – Liquid Bltizschnell & Fliest in small cracks Ideal for Porcelain, Metal, Rubber. Leather, Wood, Paper, Plastic does not support depth diving such as being used for polyethylene, polypropylene, polystyrene and soft PVC Pattex superglue gel Superfit bar & ideal for vertical surfaces Ideal for Porcelain, Metal, Rubber, Leather, Wood, Paper, Plastic randomly Suitable for PE, PP, PTFE, styrofoam, glass, glazed surfaces Flexible PVC Endfest after 24h box contents.
-50%New product
Pattex PL150 Construction Adhesive 380G Made in Germany
in-stock
Pattex PL150 Construction Adhesive 380G Made in Germany
Pattex Solvent Technology Construction Adhesive is suitable for interior and exterior applications for bonding and mounting. It ensures a permanent bond, and is UV, weather and vibration resistant.
Pattex Solvent Technology Construction Adhesive is suitable for interior and exterior applications for bonding and mounting.
High Initial Tack
For interior and exterior applications
Water-resistant
No need for solvent flashing
Basis: Solvent technology
Coverage: Approx. 300 g/cubic.cm
Final Bond Strength: Up to 6 N/sq.mm
Gap Bridging Capacity: 10mm
-50%
Pattex PU Foam 750 ml Code 1555588 German technology Made in Turkey
Last items in stock
Pattex PU Foam 750 ml Code 1555588 German technology Made in Turkey
Pattex Universal PU Foam
CHARACTERISTICS
One component PU foam for low temperature use, manual straw application
Main applications
• Insulation of window and door frames
• Mounting of window- and door frames, window sills
• Filling of cavities
• Sealing of openings in roof constructions and insulation materials
• Creating soundproof screens
• Filling of cavities around pipes
• Insulating of wall panels, roof tiles
• CFC free
Product features
One-component, moisture cure semi-rigid polyurethane foam with excellent open-closed cells balance and high mechanical strength. Product can be applied up to -10°C temperature. The foam is self-expanding and during the curing process expands about two times. It has excellent adhesion on most building materials including wood, concrete, stone, metal etc. Curing time strongly depends on the conditions. Full mechanical strength is achieved in 24 hours. Yield of the cured foam largely depends on of working conditions – temperature, air humidity, available space for expanding, etc. At minus temperatures the expansion of foam is lower and curing time longer.
APPLICATION INSTRUCTIONS
Substrate preparation
Substrates must be stable, clean and free of substances likely to impair adhesion. To ensure full and even curing of the foam, moisten substrates (brickwork, concrete, limestone) with water spray. Mask off adjacent areas. The surfaces can be moist, but not frosted or iced.
Application temperature
• Working temperature: from -10°C to +35°C.
• Can temperature: from +5°C to +30°C.
• Preferably the can should be stored at room temperature for at least 12 hours prior to use.
Application method
• Shake the can vigorously before use (15 - 20 times). Screw the foaming straw tightly onto the valve. The outflow rate of the foam can be adjusted by pressing and releasing the trigger.
• Dispense the foam sparingly; fill the seal for about 50% as the foam will expand.
• The can might be used in all positions, with the precondition that the foaming is started and ended in upside down position.
• It is vital to repeat shaking regularly during the application, especially when foaming with the can, not in upside down position.
• Remove fresh spots of foam with PU foam cleaner or acetone. Hardened foam can only be removed mechanically.
Limitations
• Limitations to joint maximal width exist in regard of ambient temperature and humidity levels.
• In dry conditions (during winter time, in rooms with central heating etc.), in order to get best foam structure and foam properties it is recommendable to fill gaps and joints in several layers by the application of smaller foam strings (up to 3 - 4 cm thickness) and slightly moisturizing between every layer.
• At very dry conditions, the foam may be brittle directly after the hardening. This brittleness is a temporary effect and disappears after a while or by warming up. Once the foam is flexible, it does not get brittle again even at cold temperatures.
• Single use should be expected.
ATTENTION! Cured PU foam must be protected from UV radiation by painting or applying a top layer of sealant, plaster, mortar, or other type of covering. Adhesion of the product is weak on polyethylene, Teflon® and on some other plastic surfaces.